R-link

[Vibro]

Давайте соберем сюда всю доступную информацию, без флуда.
В общих темах пообсуждали надобность и тема замерла. Из описания на ru -сайте понятно про музычку с видео и Том-Том.
Я накопал, что в основе Texas Instrument ARM A8 800 Mhz, модули GPS, GPRS/ EDGE (2.75G). На этой платформе скорее всего Андройд явно не выше 2.3.3 (что не так плохо) с собственной оболочкой и явно сильно залоченный. Это практически CAR-PC, только руки приложить.
Данных о видеочипе и памяти пока нет.
Еще очевидно, из предлагаемых Офами допов можно подключить парковочную камеру заднего вида и вывести графику родного парктроника.
Из обсуждений на форумах у англичан узнал, что симка у них вставляется в девайс диллером (или заводская, тут непонятно). Здесь сразу много вопросов по провайдеру. GPRS/ EDGE есть у всех, у многих 200р. в месяц анлим.
Вот в связи с выщеизложенным, обращаюсь к имеющим последние версии Dialogys - выложить для народа все что есть по R-link для РФ и по возможности для Clio у буржуев.
Язык текстов любой, но предпочтительнее русский и английский.

P.S. Пока при изучении картинок углядел железные кнопку включения и 2 громкости, для читающих 4pda на заметку.

Комментарий модератора Nemo: Важно!Запустили страничку R-Link https://ie.rlinkstore.com/en/RLink Можно обновить прошивку и карты. Появилось несколько приложений. Интернета ПОКА нет!!!

[sSpeaker]

Всем привет.
Заменил свой TomTom Live на Rlink. По размерам подошёл полностью.
GPS антенна подключилась. Разъем подошёл. Спутники видит, координаты, время и температуру показывает.
На кнопку от магнитолы реагирует(включается/отключается).
До сброса настроек рлинка подрулевой джойстик мог регулировать звук.
Джойстик на подлокотнике работает.
Парктроник тоже. Показывает расстояние на экране(цветами).
Через ЮСБ подключал флэшку - работает. Через картридер пробовал подключить SD карту от Live версии – монтируется и отваливается с ошибкой, что карта не подходит (что логично). Через другой картридер определяется как юсб драйв.
Магнитола не запустилась. Звука нет вообще. Либо чего-то не хватает, либо нужно клипом перенастроить магнитолу.
Был бы благодарен за схему подключения, если имеется.
Так же было бы интересно посмотреть в какой девайс в оригинале вставляется SD карта.

Решил разобрать. Построен на процессоре omap3630. Даташыт в гугле первый.
Стоит флешка на 2 Гб.
На плате разведён UART с доступом в консоль Linux. Ядро – 2.6.32. Android – Froyo(2.2).
По логу загрузки видно что стоит модем от sierra. Подключается к процессору по юсб. (Заменить на внешний?!)
Бутлоадер закрыт. При загрузке проверяется контрольная сума ядра.
На столе девайс включается и уходит в слип. Дальше пока не копал. Нужно сидеть в машине с ноутом.
Фотки внутренностей, распиновку УАРТ и лог загрузки смогу кинуть через несколько часов.

[sSpeaker]

Лог загрузки Rlink в машине:

Нажмите здесь, чтобы увидеть весь текст

Texas Instruments X-Loader 1.41 (Mar 30 2012 - 11:31:59)
Starting OS Bootloader from NOR ...


U-Boot 1.3.41077437-dirty (Oct  3 2012 - 17:18:30)

OMAP3630-HS rev 2, CPU-OPP2 L3-200MHz
OMAP3630 Strasbourg 1.3 Version + mDDR (Boot MMC)
DRAM:    512 MB
Using default environment

In:      serial
Out:     serial
Err:     serial

[APTS Logo/]

## Executing script at 80a25a20
get_format
-------- 1 --------
## Executing script at 80a25ddc
get_format
-------- 1 --------
Using device mmc0, partition 2

Loading from block device mmc device 0, partition 2: Name: xxa2
  Type: U-Boot  File:/uboot.conf
** File not found /uboot.conf
'uboot.conf' ignored
Hit any key to stop autoboot:  0
## Executing script at 80a257d8
get_format
-------- 1 --------
Not executing bootloader applet
Loaded device-tree at address 83300000 of length 2616 bytes
Using device mmc0, partition 2

Loading from block device mmc device 0, partition 2: Name: xxa2
  Type: U-Boot  File:/zImage

2584680 bytes read
Boot with gzipped Image
Verifying device tree...
libfdt fdt_setprop() failed
Verifying executable image signature ...

Starting kernel ...

Resetting boot powerdown watchdog
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32.9 (svc_quickbuild@nlsrvup-qbs08) (gcc version 4.3.3 (TomTom CipherWizardry 2009q1_203-474426) ) #2 PREEMPT Wed May 29 11:06:08 CEST 2013
[    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: Strasbourg A2
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] factory data: bootmem reserved successful
[    0.000000] DIE ID: 118C0002FE380000015EEBD90501901A
[    0.000000] OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk )
[    0.000000] omap_sam_base (VA) == 0xfe40f000
[    0.000000] omap_sram_start (PA) == 0x4020f000
[    0.000000] omap_sram_size (SIZE) == 0x1000
[    0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x100000
[    0.000000] Reserving 3145728 bytes SDRAM for VRAM
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: root=/dev/mmcblk0p2 console=ttyO2,115200 androidboot.console=ttyO2 sysboot_mode=cold init=/init videoout=omap24xxvout vram=0x300000,0x83000000 lpj=2334720 brick=0
[    0.000000]
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 504064KB available (4304K code, 1106K data, 492K init, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xf8000000   ( 376 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0083000   ( 492 kB)
[    0.000000]       .text : 0xc0083000 - 0xc04b7000   (4304 kB)
[    0.000000]       .data : 0xc04d2000 - 0xc0518d60   ( 284 kB)
[    0.000000] SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:402
[    0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
[    0.000000] Total of 96 interrupts on 1 active controller
[    0.000000] Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
[    0.000000] Reprogramming SDRC clock to 400000000 Hz
[    0.000000] GPMC revision 5.0
[    0.000000] OMAP GPIO hardware version 2.5
[    0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop (skipped) preset value.. 597.64 BogoMIPS (lpj=2334720)
[    0.000000] Security Framework initialized
[    0.000000] Mount-cache hash table entries: 512
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Initializing cgroup subsys freezer
[    0.000000] CPU: Testing write buffer coherency: ok
[    0.000000] regulator: core version 0.5
[    0.000000] NET: Registered protocol family 16
[    0.000000] vgpio vgpio.0: pin #403 is tagged as not connected!
[    0.000000] vgpio vgpio.0: pin #412 is tagged as not connected!
[    0.000000] vgpio vgpio.0: pin #413 is tagged as not connected!
[    0.000000] vgpio vgpio.0: pin #415 is tagged as not connected!
[    0.000000] vgpio vgpio.0: pin #423 is tagged as not connected!
[    0.000000] vgpio vgpio.0: pin #458 is tagged as not connected!
[    0.000000] vgpio vgpio.0: registered 59 GPIOs (@400)
[    0.000000] Strasbourg_tvp515x: Driver registration Starting
[    0.000000] Strasbourg_tvp515x: Driver registration complete
[    1.390869] OMAP DMA hardware revision 5.0
[    1.390930] Reserving DMA channels 0 and 1 for HS ROM code
[    1.391937] offenburg::flipflop: Registered
[    1.392333] omap_vout: Driver registration starting
[    1.411132] bio: create slab <bio-0> at 0
[    1.413055] SCSI subsystem initialized
[    1.415679] usbcore: registered new interface driver usbfs
[    1.415924] usbcore: registered new interface driver hub
[    1.416168] usbcore: registered new device driver usb
[    1.416595] i2c_omap i2c_omap.1: bus 1 rev4.0 at 400 kHz
[    1.441986] twl4030: PIH (irq 7) chaining IRQs 368..375
[    1.442016] twl4030: power (irq 373) chaining IRQs 376..383
[    1.442382] twl4030: gpio (irq 368) chaining IRQs 384..401
[    1.444244] vgpio vgpio.1: pin #600 is tagged as not connected!
[    1.444396] vgpio vgpio.1: pin #602 is tagged as not connected!
[    1.444641] vgpio vgpio.1: registered 5 GPIOs (@600)
[    1.445709] regulator: VUSB1V5: 1500 mV normal standby
[    1.446166] regulator: VUSB1V8: 1800 mV normal standby
[    1.446594] regulator: VUSB3V1: 3100 mV normal standby
[    1.448333] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[    1.449188] regulator: VMMC1: 3000 mV normal standby
[    1.449645] regulator: VDAC: 1800 mV normal standby
[    1.450561] regulator: VAUX2: 1800 mV normal standby
[    1.451019] regulator: VDVI: 1800 mV normal standby
[    1.451934] regulator: VAUX1: 3000 mV normal standby
[    1.452911] regulator: VAUX3: 1800 mV normal standby
[    1.453094] i2c_omap i2c_omap.2: bus 2 rev4.0 at 100 kHz
[    1.453582] i2c_omap i2c_omap.3: bus 3 rev4.0 at 50 kHz
[    1.454193] LinuxPPS API ver. 1 registered
[    1.454193] Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.455871] Bluetooth: Core ver 2.15
[    1.456115] NET: Registered protocol family 31
[    1.456146] Bluetooth: HCI device and connection manager initialized
[    1.456146] Bluetooth: HCI socket layer initialized
[    1.961791] Switching to clocksource 32k_counter
[    1.964508] musb_hdrc: version 6.0, musb-dma, peripheral, debug=0
[    1.964569] musb_init_controller: doing clk_get
[    1.964721] musb_hdrc: USB Peripheral mode controller at fa0ab000 using DMA, IRQ 92
[    1.965118] NET: Registered protocol family 2
[    1.965240] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    1.965454] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    1.965881] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    1.966186] TCP: Hash tables configured (established 16384 bind 16384)
[    1.966217] TCP reno registered
[    1.966308] NET: Registered protocol family 1
[    1.973419] dspbridge_init: 600000 bytes @ 80a00000
[    1.975097] Strasbourg: power supply driver loaded
[    1.975311] omap-iommu omap-iommu.0: isp registered
[    1.976104] iovmm-omap initialized isp, major: 252, base-minor: 0
[    1.976715] fdtexport driver, (c) 2009 TomTom BV
[    1.977416] ttcrypto: found version 1 tt_crypto context
[    1.991088] ashmem: initialized
[    1.991424] msgmni has been set to 985
[    1.992340] alg: No test for stdrng (krng)
[    1.992401] io scheduler noop registered (default)
[    2.047912] OMAP DSS rev 2.0
[    2.047973] OMAP DISPC rev 3.0
[    2.048034] OMAP VENC rev 2
[    2.048370] OMAP DSI rev 1.0
[    2.066467] Loop count exceeded in check SR I2C write
[    2.067687] omap-hsuart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
[    2.068206] omap-hsuart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
[    2.068572] omap-hsuart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
[    2.757598] console [ttyO2] enabled
[    2.761505] Hiding boot partition 0...
[    2.767150] mmc0: new high speed MMC card at address 0001
[    2.773956] mmcblk0: mmc0:0001 M2G1HF 1.86 GiB
[    2.780364]  mmcblk0: p2
[    2.786499] loop: module loaded
[    2.792358] PPP generic driver version 2.4.2
[    2.797332] PPP Deflate Compression module registered
[    2.802795] PPP BSD Compression module registered
[    2.807769] tun: Universal TUN/TAP device driver, 1.6
[    2.813079] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    2.819915] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.828460] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[    2.834564] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[    2.842529] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[    2.860382] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[    2.867065] usb usb1: configuration #1 chosen from 1 choice
[    2.873382] hub 1-0:1.0: USB hub found
[    2.877441] hub 1-0:1.0: 3 ports detected
[    2.985351] ehci-omap ehci-omap.0: Resetting the 5V75 VBUS line...
[    3.040557] usbcore: registered new interface driver cdc_acm
[    3.046508] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[    3.055511] Initializing USB Mass Storage driver...
[    3.061065] usbcore: registered new interface driver usb-storage
[    3.067443] USB Mass Storage support registered.
[    3.072570] usbcore: registered new interface driver libusual
[    3.079071] usbcore: registered new interface driver usbserial
[    3.085235] usbserial: USB Serial Driver core
[    3.090057] USB Serial support registered for GSM modem (1-port)
[    3.096679] usbcore: registered new interface driver option
[    3.102539] option: v0.7.2:USB Driver for GSM modems
[    3.107971] USB Serial support registered for Sierra USB modem
[    3.114318] usbcore: registered new interface driver sierra
[    3.120239] sierra: v.1.3.8:USB Driver for Sierra Wireless USB modems
[    3.127227] usbcore: registered new interface driver usb_ehset_test
[    3.134185] android_register_function acm
[    3.140350] using rtc device, twl_rtc, for alarms
[    3.145294] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[    3.152130] twl_rtc twl_rtc: Power up reset detected.
[    3.158111] twl_rtc twl_rtc: Enabling TWL-RTC.
[    3.163452] i2c /dev entries driver
[    3.170501] Linux video capture interface: v2.00
[    3.177001] omap-previewer omap-previewer: omap-previewer: Registered preview wrapper
[    3.186859] omap3isp omap3isp: Revision 15.0 found
[    3.192047] omap-iommu omap-iommu.0: isp: version 1.1
[    3.201599] OMAP hwmon driver
[    3.207458] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[    3.214660] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    3.223632] Bluetooth: HCI UART driver ver 2.2
[    3.228332] Bluetooth: HCI H4 protocol initialized
[    3.233367] Bluetooth: HCI BCSP protocol initialized
[    3.238586] Bluetooth: HCILL protocol initialized
[    3.243560] cpuidle: using governor ladder
[    3.247863] cpuidle: using governor menu
[    3.253631] usbcore: registered new interface driver usbhid
[    3.259582] usbhid: v2.6:USB HID core driver
[    3.264831] logger: created 64K log 'log_main'
[    3.269897] logger: created 256K log 'log_events'
[    3.275146] logger: created 64K log 'log_radio'
[    3.280151] logger: created 64K log 'log_system'
[    3.285614] CSR_BC: csr-bc: Probing CSR BlueCore mode driver.
[    3.292388] tomtom-gps Driver: Probed.
[    3.296325] gps: device registration: name="offenburg"
[    3.302124] tomtom-gps Driver: Registering rfkill for GPS.
[    3.308135] tomtom-gps Driver: Initialized.
[    3.312744] flipflop driver, (c) 2009 TomTom BV
[    3.317810] TomTom CAN-Microprocessor Driver, (C) 2008 TomTom BV
[    3.325408] new PPS source tomtom-pps at ID 0
[    3.330108] tomtom-pps tomtom-pps: successfully registered pps source at 0.
[    3.337646] tomtom-pps: successfully registered driver.
[    3.343139] suicide_alarm driver, (c) 2011 TomTom BV
[    3.348937] Advanced Linux Sound Architecture Driver Version 1.0.21.
[    3.356353] ALSA device list:
[    3.359466]   No soundcards found.
[    3.363128] Netfilter messages via NETLINK v0.30.
[    3.368194] nf_conntrack version 0.5.0 (7882 buckets, 31528 max)
[    3.374755] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    3.382568] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    3.390899] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    3.397521] ctnetlink v0.93: registering with nfnetlink.
[    3.403320] ip_tables: (C) 2000-2006 Netfilter Core Team
[    3.409057] TCP cubic registered
[    3.412475] NET: Registered protocol family 17
[    3.417205] Bluetooth: L2CAP ver 2.14
[    3.421051] Bluetooth: L2CAP socket layer initialized
[    3.426391] Bluetooth: SCO (Voice Link) ver 0.6
[    3.431152] Bluetooth: SCO socket layer initialized
[    3.436492] Bluetooth: RFCOMM TTY layer initialized
[    3.441680] Bluetooth: RFCOMM socket layer initialized
[    3.447113] Bluetooth: RFCOMM ver 1.11
[    3.451049] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    3.456665] Bluetooth: BNEP filters: protocol multicast
[    3.462188] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    3.469024] Power Management for TI OMAP3.
[    3.475189] Unable to Changelevel for resource vdd1_opp to 0
[    3.481201] Error: could not refresh resources
[    3.486450] SR: Nvalues not fused for 1.2G, disabled
[    3.491668] SR: Nvalues not fused for 1G, disabled
[    3.496795] SR2:Fused Nvalues for VDD1OPP3 11193534
[    3.501953] SR2:Fused Nvalues for VDD1OPP2 10126585
[    3.507080] SR2:Fused Nvalues for VDD1OPP1 10082000
[    3.512207] sr1_opp_margin[1]=37500
[    3.515869] sr1_opp_margin[2]=37500
[    3.519561] sr1_opp_margin[3]=37500
[    3.523223] steps added, volt will be recaliberated automatically
[    3.529663] SR2:Fused Nvalues for VDD2OPP1 99f2eb
[    3.534637] SR2:Fused Nvalues for VDD2OPP2 10066063
[    3.539794] SmartReflex driver initialized
[    4.865386] clock: dpll2_ck failed transition to 'bypassed'
[    4.919281] at24 3-0050: 8192 byte at24 EEPROM (writable)
[    4.928222] input: TSC2007 Touchscreen as /devices/virtual/input/input0
[    4.935974] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[    4.945037] DMA transaction error with device 0
[    4.950378] OMAP DISPCONTROL read (stallmode)0
[    4.955108] OMAP DISPCONTROL read (gpout)1
[    4.959381] OMAP DISPCONTROL read (stallmode)1
[    4.964721] DPI set dsi clk
[    5.110778] DPI set dsi clk
[    5.123504] regulator_init_complete: incomplete constraints, leaving VAUX3 on
[    5.131378] regulator_init_complete: incomplete constraints, leaving VAUX1 on
[    5.139038] regulator_init_complete: incomplete constraints, leaving VAUX2 on
[    5.148986] twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:01 UTC (946684801)
[    5.157836] omap3 omap3isp CSI memvs initted
[    5.163146] Registered led device: lcd-backlight
[    5.168304] Freeing init memory: 492K
[APTS InitRamFS]

TOMTOM initramfs compiled on May 29 2013 11:04:56

initramfs: BOOTMODE: cold

AUTOTEST: root=/dev/mmcblk0p2

initramfs: Checking filesystem on: /dev/mmcblk0p2

Opening the watchdog...
Kicking the watchdog... (3)

/dev/mmcblk0p2: recovering journal
/dev/mmcblk0p2: Superblock last mount time is in the future.  FIXED.
/dev/mmcblk0p2: clean, 2246/122400 files, 104805/488416 bl[    7.011779] omap_wdt: Unexpected close, not stopping!
ocks
initramfs: fsck returned: 0
initramfs: Attempti[    7.021881] kjournald starting.  Commit interval 5 seconds
ng to mount /dev/mmcblk0p2 on /internalstorage...

initramfs: [    7.033050] EXT3 FS on mmcblk0p2, Trying to mount internal journal
/dev/mmcblk0p2 a[    7.040832] EXT3-fs: mounted filesystem with ordered data mode.
s ext3 (options=barrier=1)
initramfs: Checking for system update from directory[    7.054595] signedloop: using 76866 data pages, 377 L0 pages and 2 L1 pages
 data/ttcontent/common/installed.

initramfs: Failed to stat zImage due to No such file or directory.

initramfs: Checking for system update from directory data/ttcontent.

initramfs: Failed to stat zImage due to No such file or directory.

initramfs: Setting up loop device /dev/loop0 using rootfs.img

initramfs: Creating root filesystem...

initramfs: Trying to mount /dev/loop0 as squashfs (options=none)
[    7.116546] signedloop: activated hash checking on device loop0
initramfs: Trying to mount /dev/loop0 as ext3 (options=barrier=1)
[    7.130493] EXT3-fs: mounted filesystem with ordered data mode.
[    7.136749] kjournald starting.  Commit interval 5 seconds
AUTOTEST: NAVCORE starting

[    7.151153] omap_wdt: Unexpected close, not stopping!
initramfs: Checking CAN firmware

[    7.169647] Process /system/bin/can_firmware_tool requested an executable stack, ignoring...
can_swl: GetDesiredSwVersion(): No file named /system/ttdaemon/can_micro_firmware/mfd_can_app1.img
can_swl: File /system/ttdaemon/can_micro_fir[    7.229034] omap_wdt: Unexpected close, not stopping!
mware/mfd_can_app1.img not available, try the backward compatible file /system/ttdaemon/can_micro_firmware/strasbourg_can_app1.img.
can_swl: GetDesiredSwVersion(): No file named /system/ttdaemon/can_micro_firmware/strasbourg_can_app1.img
can_swl: DoCanMicroVersionCheck: bootloader:1177652->0 application:1177652->1177652
can_swl: There is no desired CAN micro bootloader SW version. The CAN micro bootloader SW upgrade mechanism is blocked.
can_swl: Actual CAN micro application SW version is as desired: 1177652
initramfs: can firmware matches

initramfs: Checking EOL settings

initramfs: EOL s[    7.439331] omap_wdt: Unexpected close, not stopping!
ettings: CONFIGURED

[/APTS InitRamFS]

AUTOTEST: starting init

[    7.772521] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[    8.050537] Process /system/bin/fortytwo requested an executable stack, ignoring...
[    8.578277] No device for DAI BC6
[    8.668670] proc_load: Processor Loaded /system/lib/dsp/baseimage.dof
[    8.676116] omap mailbox rev 4.0
[    8.682373] proc_start: dsp in running state
[    8.687194] procwrap_detach: deprecated dspbridge ioctl
[    8.698944] No device for DAI omap-mcbsp-dai-0
[    8.704040] No device for DAI omap-mcbsp-dai-1
[    8.708862] No device for DAI omap-mcbsp-dai-2
[    8.714385] No device for DAI omap-mcbsp-dai-3
[    8.719085] No device for DAI omap-mcbsp-dai-4
[    8.801971] No device for DAI twl4030
[    8.806121] No device for DAI twl4030 Voice
[    8.810607] No device for DAI twl4030 Clock
[    8.921630] No device for DAI UDA1334
[    9.001617] Strasbourg SoC init
[    9.008483] TWL4030 Audio Codec init
[    9.014129] asoc: twl4030 <-> omap-mcbsp-dai-0 mapping ok
[    9.020324] asoc: BC6 <-> omap-mcbsp-dai-2 mapping ok
[    9.132324] UDA1334 Audio Codec 0.1
[    9.136566] asoc: UDA1334 <-> omap-mcbsp-dai-1 mapping ok
[    9.455963] usbcore: registered new interface driver snd-usb-audio
[    9.646820] Video decoder chip id 5151 detected!
[    9.666351] Registered tvp5150 video decoder
[    9.746856] omap_vout: registered and initialized video device 3 [v4l2]
[    9.920623] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    9.927612] ohci-omap3 ohci-omap3.0: OMAP3 OHCI Host Controller
[    9.934906] ohci-omap3 ohci-omap3.0: new USB bus registered, assigned bus number 2
[    9.942993] ohci-omap3 ohci-omap3.0: irq 76, io mem 0x48064400
[   10.055938] usb usb2: configuration #1 chosen from 1 choice
[   10.062408] hub 2-0:1.0: USB hub found
[   10.071594] hub 2-0:1.0: 3 ports detected
[   10.094787] ohci-omap3 ohci-omap3.0: trigging poll (state: 1)...
[   10.263977] omapflash: Found 1 x16 devices at 0x0 in 16-bit bank
[   10.270996]  Intel/Sharp Extended Query Table at 0x0039
[   10.276641]  Intel/Sharp Extended Query Table at 0x0039
[   10.282104]  Intel/Sharp Extended Query Table at 0x0039
[   10.287658]  Intel/Sharp Extended Query Table at 0x0039
[   10.293212]  Intel/Sharp Extended Query Table at 0x0039
[   10.298767]  Intel/Sharp Extended Query Table at 0x0039
[   10.304321] Using auto-unlock on power-up/resume
[   10.309295] cfi_cmdset_0001: Erase suspend on write enabled
[   10.315917] cmdlinepart partition parsing not available
[   10.321502] Creating 1 MTD partitions on "omapflash":
[   10.326782] 0x000000000000-0x000000400000 : "nor_part0"
[   10.344787] ohci-omap3 ohci-omap3.0: trigging poll (state: 1)...
[   10.594757] ohci-omap3 ohci-omap3.0: trigging poll (state: 1)...
[   10.844757] ohci-omap3 ohci-omap3.0: trigging poll (state: 1)...
[   11.094787] ohci-omap3 ohci-omap3.0: trigging poll (state: 1)...
[   11.240936] input: MSM-keypad as /devices/virtual/input/input1
[   11.249267] input: CSW-keypad as /devices/virtual/input/input2
[   11.817779] Callback set_scenario not implemented in /opt/buildagent/workspace/root/platform/Froyo/Nightly/p-a-strasbourgmfd10-kz/ngl-strbdev-main/Strasbourg-build-noprepare/platform/mydroid/kernel/android-2.6.32/drivers/tomtom/sound/uda1334.c
[   12.720703] warning: `zygote' uses 32-bit capabilities (legacy support in use)
[/APTS Android started][   20.658660] request_suspend_state: wakeup (3->0) at 19314056442 (2000-01-01 00:00:17.009674064 UTC)
[   27.700958] Callback set_scenario not implemented in /opt/buildagent/workspace/root/platform/Froyo/Nightly/p-a-strasbourgmfd10-kz/ngl-strbdev-main/Strasbourg-build-noprepare/platform/mydroid/kernel/android-2.6.32/drivers/tomtom/sound/uda1334.c
[   28.014892] OMAP DISPCONTROL read (stallmode)0
[   28.026184] OMAP DISPCONTROL read (gpout)1
[   28.052947] OMAP DISPCONTROL read (stallmode)1
[   28.066070] DPI set dsi clk
[   28.243804] DPI set dsi clk

---------- Сообщение добавлено в 12:51 ---------- Предыдущее сообщение размещено в 11:33 ----------

Фотки плати:

Нажмите здесь, чтобы увидеть весь текст

Лицевая сторона плати;
Задняя ;
CPU;
Распиновка УАРТ;
Припаянный UART;

Больше тут.

После полной загрузки устройство не запускает шелл. Команды вводить в консоли нельзя.

Рассуждения по взлому/доступу к ОС:

Нажмите здесь, чтобы увидеть весь текст

На фотке CPU, справа за шылдом, видно семь резисторов и цифры "1001101".
Скорей всего это выбор загрузочного устройства.
Инфа с даташыта:

Six external pins (sys_boot[5:0]) are used to select interfaces or devices for booting. The sys_boot[6] pin
is used to select whether the internal oscillator is bypassed.

***
Depending on sys_boot pin
configuration during the reset (leftmost column), the ROM code tries to boot on the first booting device
listed. If the boot fails on this first booting device, the ROM code tries the second booting device, then the
third, then the fourth.

Сейчас стоит:

Booting Sequence When SYS.BOOT[5] = 0
0b10011 = XIP -> UART3

Если изменить SYS.BOOT[5] на 1, то выйдет: UART3 -> XIP.
Потом можно будет грузить свой bootloader через уарт, изменять ядро, патчить navcore и т.д.

[Дмитрий290481]

И ЧТО ДЕЛАТЬ. А В МАШИНЕ ВСЕ РАБОТАЕТ

[igormo]

Хм... Сегодня карта вообще не прочиталась, хотя всего и -6 на улице. Посмотрим завтра утром после гаража. Каб не умерла...

[igormo]

короче коллеги, думал умерла карта, но похоже дело посерьезней.
не читается и карта и USB. то есть если вставляешь флэшку то пишет USB обнаружен и всё.
в меню медиа ее не видно, как и CD карту.
значит проблемы всё-таки в аппарате.
кто-нить знает, а ресет там можно на мультимедии сделать как-то? или не поможет?

[Борис65]

Скинуть клемму с АКБ, покурить, накинуть клемму. Для начала.

[det64]

Подскажите а два телефона в R-Linke могут работать одновременно в режиме ожидания звонков??????????????

[Roman12310]

det64, нет. только один

[igormo]

Сообщение от igormo

короче коллеги, думал умерла карта, но похоже дело посерьезней.
не читается и карта и USB. то есть если вставляешь флэшку то пишет USB обнаружен и всё.
в меню медиа ее не видно, как и CD карту.
значит проблемы всё-таки в аппарате.
кто-нить знает, а ресет там можно на мультимедии сделать как-то? или не поможет?

короче был на станции, перезагрузили систему, всё заработало. заодно ТО1 сделал, все равно через 3 недели срок подходит.

[vectos]

Для справки- у ОД Тринити Трейд в Калининграде работает специалист диагностики, который выполняет процедуру, после которой R-Link видит камеру заднего вида. Сегодня я в этом убедился, всё работает.